 |
These (UL) Approved Riser / FPLR-rated cables have been designed specifically and approved by the NEC (National Electric Code) for use in fire alarms and signal control circuits, as well as other fire protection devices, and are rated for installation for use in between floors and in non-plenum areas. They are rated NEC 760 FPLR, 800CMR, and 725 CL2R This cable is not recommended for outdoor use or direct burial
Sunshine's 16 AWG cable is made of two solid bare 100% copper conductors color-coded Black and Red. The cable is shielded with an aluminum mylar shield and has a solid 24 AWG tinned copper drain wire. It is rated for 300 volts 75C. This cable has a (UL) approved Red PVC jacket. A rip cord is included for easy stripping
This cable has a diameter of .178” and weighs 29# per 1000 Feet. Footage markings have been added to the jacket so you can always determine the amount remaining on the spool. The cable ships on a 12” diameter plywood spool
All Sunshine products are proudly made in China & Vietnam! Have a job that needs another conductor count or requires a different length or different color jacket? Sunshine offers a selection of hundreds of electronic & fire alarm cables, rated Riser or Plenum in non-shielded or shielded configurations.
Sunshine's FPLP cable is made of two solid bare 100% copper conductors color-coded Black and Red insulated with Low Smoke PVC. Sunshine provides this cable with your choice of 5 different Low Smoke PVC Jacket colors for circuit identification.
Sunshine's FPLR cable is made of two solid bare 100% copper conductors color-coded Black and Red. This cable has a (UL) approved Red PVC jacket. A rip cord is included for easy stripping.
Both FPLR and FPLP cables are rated for 300 volts 75C. Footage markings have been added to the jacket so you can always determine the amount remaining on the spool. The cable ships on a 12” diameter plywood spool.
This Sunshine 500-foot red 16/2 fire alarm/security cable comes in an easy-to-use pull box. The cable is composed of 2 16 AWG (American Wire Gauge) wires inside of a FPLR-rated outer jacket. The primary use of this cable is for power-limited fire circuits, but it also finds use in the wiring of security systems. (Often one finds the two systems are closely tied together.)
Our security/fire alarm cables listed as FPLR (Fire-Power Limited-Riser) meet characteristics defined under UL 1424. This cable is intended for installation in vertical runs in which the length exceeds one floor. This is specified in section 760-154(B) of the National Electrical Code ANSI/NFPA 70. These cables also meet UL 1666 meaning that fall within flame-propagation height rules.
Our OEM/ODM Certified Fire Alarm Cable is designed to provide great service for all our customers to ensure they help boost your business with Fire Alarm Cable. We could supply high-quality Fire Alarm Cable that are applicable in different approaches to give you flexibility and an advantage in the market. Our certified Fire Alarm Cable provides high speed, high definition and super clear sound for you when applying to different situations. Besides, the portable Fire Alarm Cable is brought to any place if you need Fire Alarm Cable. Getting best Fire Alarm Cable wholesale gives you a great benefit that you can take advantage of in different applications.
Sunshine Electronics has been working as a trustworthy Fire Alarm Cable manufacturer and supplier in China and outside China--Vietnam for almost 20 years. During the period of those manufacturing years in the field of cable, we gain abundant experience in it. We can guarantee that Fire Alarm Cable is produced with high quality in China and Vietnam. Besides manufacturing CAT Cables, we also offer customization and design services to you. We could provide a variety of colors, shapes, and sizes.
Through our modern manufacturing services for Fire Alarm Cable, we reduce your costs, ensure high-quality and certified Fire Alarm Cable, speed up your certified Fire Alarm Cable to the market, and help you gain a competitive edge. With more than 1200 employees distributed in China and outside China--Vietnam, devotes themselves to serving our overseas customers, and providing them with more advantages and chances to occupy the charger market. Owing to advanced R&D for Fire Alarm Cable, rigorous quality control for Fire Alarm Cable, consistent automated production lines for Fire Alarm Cable, flexible manufacturing system and dynamic dispatching in China and Vietnam, we have gained more reliability and credibility in this industry to obtain more market share and opportunities for our global customers building long-term stable cooperation and maintaining a strong friendship with them in Western Europe, North America, Australia, and Asia.
Sunshine Electronics has become one of the most well-trusted Fire Alarm Cable manufacturers and suppliers in both China and outside China--in Vietnam. We are available to provide two production lines for Fire Alarm Cable in China and Vietnam at the same time, which means not only we could supply in bulk to meet your high-volume requirements, but also you could decide whether to dispatch your Fire Alarm Cable from China or Vietnam. The most important factor is that Fire Alarm Cable produced in China and Vietnam are all of high quality and certified, and the specifications of Fire Alarm Cable in China and Vietnam are all the same.
Our professional Fire Alarm Cable manufacturing processes are streamlined, standardized, and rigorous to guarantee that we can always provide high-quality and certified Fire Alarm Cable to all our customers. We adopt machines with highly Validated and Recognized test equipment brands in our laboratories and production workshop, such as FLUKE, Chroma, YOKOGAWA, LECROY, TESEQ, and GwinSTEK which stand for the highest and strictest standards with strong recognition in this industry of Fire Alarm Cable. At first, in terms of materials of Fire Alarm Cable, they should conform to the standards of RoHS, Reach, California 45 Act, and Red Phosphorus free. Then, all Fire Alarm Cable will follow a series of verification. At last, before dispatching and packaging, all Fire Alarm Cable must pass another series of product verification, such as UL &CUL, FCC, DOE, CE, and NRCan.
Our expert team of designers who are talented in the field of Fire Alarm Cable handles the packaging and design solutions for Fire Alarm Cable from the beginning to the end, catering to any business needs. Combining the product design of Fire Alarm Cable, they are responsible for creating the perfect appearance design for your Fire Alarm Cable, along with matching labeling services of Fire Alarm Cable, and packaging of Fire Alarm Cable.
We are skilled in providing assistance in inventory management of Fire Alarm Cable through the use of our order system of Fire Alarm Cable and delivery options of Fire Alarm Cable. We are also good at managing the internal inventory to make sure that we have available stock of Fire Alarm Cable for faster delivery to our customers who are willing to use our Fire Alarm Cable. We can promise that we will solve your urgent need for Fire Alarm Cable as soon as possible to ascertain to leave a great impression on our packing services.
We believe in walking the journey with you which is why we deliver after-sales services designed to give you a hand whenever you are stuck and we are there till the last second of your Fire Alarm Cable.
Our Fire Alarm Cable shows custom options for you, such as the color of Fire Alarm Cable, the shape of Fire Alarm Cable, the size of Fire Alarm Cable, the labeling service of Fire Alarm Cable, and the package of Fire Alarm Cable on the surface of Fire Alarm Cable. But if you can’t find what you need for Fire Alarm Cable or you already have specific requirements for Fire Alarm Cable, no need to worry! We accept custom orders of Fire Alarm Cable according to your ideas. Contact us, let us know what you need for Fire Alarm Cable, and we’ll do our best to create the best Fire Alarm Cable for your business!
Adding extra value to your Fire Alarm Cable by choosing a suitable Fire Alarm Cable design is also a key element to boost your brand in promoting Fire Alarm Cable. Fashionable, technical, and practical shapes for Fire Alarm Cable or packages for Fire Alarm Cable could increase customers’ desire to try your Fire Alarm Cable. By creating a specialized label for Fire Alarm Cable or a design of Fire Alarm Cable, it is easier to create a better and more lasting impression on your target market for selling Fire Alarm Cable.
After completing the production of your Fire Alarm Cable, our selection of labels as well as packages for Fire Alarm Cable is designed to cater to your special wants if your need to add your trademarks on the surface of Fire Alarm Cable. We offer different designs for Fire Alarm Cable and types of packages for Fire Alarm Cable that can drastically enhance the way your Fire Alarm Cable is consumed. Custom labeling services can also be requested to complement your unique needs for Fire Alarm Cable. Contact us now!
Sunshine Electronics targets at supplying the best customer experience in the whole cooperation process of Fire Alarm Cable. We also offer free samples for Fire Alarm Cable to all clients who are willing to have a try on our high-quality Fire Alarm Cable. After getting your free samples of Fire Alarm Cable, you can check and examine our Fire Alarm Cable if our Fire Alarm Cable meets your requirements. We undoubtedly possess the confidence that our Fire Alarm Cable is of premium quality and you will not regret.
Fire Alarm Cable meets the following industry standards:
Fire Alarm cable is composed of solid bare conductors. Our Fire Alarm cable is also twisted for maximum flexibility. A fire Alarm cable is also available in Riser or Plenum. The fire Alarm can also be shielded with aluminum foil and a stranded tinned copper drain wire.
In fire alarm systems, the real difference between Class B and Class A is that if the pathway is interrupted, Class B only sends a "Failure Signal" to the panel, and Class A provides an extra path to get around the interruption.
According to NEC Articles 760 and 725, there are two types of fire alarm system circuits: power restricted and non-power-limited. Power Limited Fire Alarm Wires typically work at 24 volts DC, whereas non-power-limited cables run at 120 volts AC.
Type 1 - Cable with a resistance of fewer than 100 Ohms/km and low smoke zero halogen insulating and sheathing. Type 2 - Cable with a resistance of fewer than 100 Ohms/km and PVC insulation and sheathing.
Conduit or not to Conduit? NFPA and NEC 90 articles state that when installing a fire alarm system, any fire alarm wiring below 7 feet or in non-accessible areas must be installed in a metallic raceway, including behind drywall walls or hard ceiling surfaces.
If fire alarm cabling does not have other wires or cabling nearby or other sources of electrical interference, you may not need shielding. But in facilities near heavy electrical or mechanical equipment, the interference from these devices might mean you should use shielding to protect the fire alarm cable.
Power-limited fire alarm circuit cables and conductors shall not be placed in any cable, cable tray, compartment, enclosure, manhole, outlet box, device box, raceway, or similar fitting with conductors of electric light, power, Class 1, non—power-limited fire alarm circuits, and medium-power network-powered broadband ...
These (UL) Approved Riser / FPLR-rated cables have been designed specifically and approved by the NEC (National Electric Code) for use in fire alarms and signal control circuits, as well as other fire protection devices, and are rated for installation for use in between floors and in non-plenum areas. They are rated NEC 760 FPLR, 800CMR, and 725 CL2R This cable is not recommended for outdoor use or direct burial
Sunshine's 16 AWG cable is made of two solid bare 100% copper conductors color-coded Black and Red. The cable is shielded with an aluminum mylar shield and has a solid 24 AWG tinned copper drain wire. It is rated for 300 volts 75C. This cable has a (UL) approved Red PVC jacket. A rip cord is included for easy stripping
This cable has a diameter of .178” and weighs 29# per 1000 Feet. Footage markings have been added to the jacket so you can always determine the amount remaining on the spool. The cable ships on a 12” diameter plywood spool
All Sunshine products are proudly made in China & Vietnam! Have a job that needs another conductor count or requires a different length or different color jacket? Sunshine offers a selection of hundreds of electronic & fire alarm cables, rated Riser or Plenum in non-shielded or shielded configurations.
Sunshine's FPLP cable is made of two solid bare 100% copper conductors color-coded Black and Red insulated with Low Smoke PVC. Sunshine provides this cable with your choice of 5 different Low Smoke PVC Jacket colors for circuit identification.
Sunshine's FPLR cable is made of two solid bare 100% copper conductors color-coded Black and Red. This cable has a (UL) approved Red PVC jacket. A rip cord is included for easy stripping.
Both FPLR and FPLP cables are rated for 300 volts 75C. Footage markings have been added to the jacket so you can always determine the amount remaining on the spool. The cable ships on a 12” diameter plywood spool.
This Sunshine 500-foot red 16/2 fire alarm/security cable comes in an easy-to-use pull box. The cable is composed of 2 16 AWG (American Wire Gauge) wires inside of a FPLR-rated outer jacket. The primary use of this cable is for power-limited fire circuits, but it also finds use in the wiring of security systems. (Often one finds the two systems are closely tied together.)
Our security/fire alarm cables listed as FPLR (Fire-Power Limited-Riser) meet characteristics defined under UL 1424. This cable is intended for installation in vertical runs in which the length exceeds one floor. This is specified in section 760-154(B) of the National Electrical Code ANSI/NFPA 70. These cables also meet UL 1666 meaning that fall within flame-propagation height rules.
Our OEM/ODM Certified Fire Alarm Cable is designed to provide great service for all our customers to ensure they help boost your business with Fire Alarm Cable. We could supply high-quality Fire Alarm Cable that are applicable in different approaches to give you flexibility and an advantage in the market. Our certified Fire Alarm Cable provides high speed, high definition and super clear sound for you when applying to different situations. Besides, the portable Fire Alarm Cable is brought to any place if you need Fire Alarm Cable. Getting best Fire Alarm Cable wholesale gives you a great benefit that you can take advantage of in different applications.
Sunshine Electronics has been working as a trustworthy Fire Alarm Cable manufacturer and supplier in China and outside China--Vietnam for almost 20 years. During the period of those manufacturing years in the field of cable, we gain abundant experience in it. We can guarantee that Fire Alarm Cable is produced with high quality in China and Vietnam. Besides manufacturing CAT Cables, we also offer customization and design services to you. We could provide a variety of colors, shapes, and sizes.
Through our modern manufacturing services for Fire Alarm Cable, we reduce your costs, ensure high-quality and certified Fire Alarm Cable, speed up your certified Fire Alarm Cable to the market, and help you gain a competitive edge. With more than 1200 employees distributed in China and outside China--Vietnam, devotes themselves to serving our overseas customers, and providing them with more advantages and chances to occupy the charger market. Owing to advanced R&D for Fire Alarm Cable, rigorous quality control for Fire Alarm Cable, consistent automated production lines for Fire Alarm Cable, flexible manufacturing system and dynamic dispatching in China and Vietnam, we have gained more reliability and credibility in this industry to obtain more market share and opportunities for our global customers building long-term stable cooperation and maintaining a strong friendship with them in Western Europe, North America, Australia, and Asia.
Sunshine Electronics has become one of the most well-trusted Fire Alarm Cable manufacturers and suppliers in both China and outside China--in Vietnam. We are available to provide two production lines for Fire Alarm Cable in China and Vietnam at the same time, which means not only we could supply in bulk to meet your high-volume requirements, but also you could decide whether to dispatch your Fire Alarm Cable from China or Vietnam. The most important factor is that Fire Alarm Cable produced in China and Vietnam are all of high quality and certified, and the specifications of Fire Alarm Cable in China and Vietnam are all the same.
Our professional Fire Alarm Cable manufacturing processes are streamlined, standardized, and rigorous to guarantee that we can always provide high-quality and certified Fire Alarm Cable to all our customers. We adopt machines with highly Validated and Recognized test equipment brands in our laboratories and production workshop, such as FLUKE, Chroma, YOKOGAWA, LECROY, TESEQ, and GwinSTEK which stand for the highest and strictest standards with strong recognition in this industry of Fire Alarm Cable. At first, in terms of materials of Fire Alarm Cable, they should conform to the standards of RoHS, Reach, California 45 Act, and Red Phosphorus free. Then, all Fire Alarm Cable will follow a series of verification. At last, before dispatching and packaging, all Fire Alarm Cable must pass another series of product verification, such as UL &CUL, FCC, DOE, CE, and NRCan.
Our expert team of designers who are talented in the field of Fire Alarm Cable handles the packaging and design solutions for Fire Alarm Cable from the beginning to the end, catering to any business needs. Combining the product design of Fire Alarm Cable, they are responsible for creating the perfect appearance design for your Fire Alarm Cable, along with matching labeling services of Fire Alarm Cable, and packaging of Fire Alarm Cable.
We are skilled in providing assistance in inventory management of Fire Alarm Cable through the use of our order system of Fire Alarm Cable and delivery options of Fire Alarm Cable. We are also good at managing the internal inventory to make sure that we have available stock of Fire Alarm Cable for faster delivery to our customers who are willing to use our Fire Alarm Cable. We can promise that we will solve your urgent need for Fire Alarm Cable as soon as possible to ascertain to leave a great impression on our packing services.
We believe in walking the journey with you which is why we deliver after-sales services designed to give you a hand whenever you are stuck and we are there till the last second of your Fire Alarm Cable.
Our Fire Alarm Cable shows custom options for you, such as the color of Fire Alarm Cable, the shape of Fire Alarm Cable, the size of Fire Alarm Cable, the labeling service of Fire Alarm Cable, and the package of Fire Alarm Cable on the surface of Fire Alarm Cable. But if you can’t find what you need for Fire Alarm Cable or you already have specific requirements for Fire Alarm Cable, no need to worry! We accept custom orders of Fire Alarm Cable according to your ideas. Contact us, let us know what you need for Fire Alarm Cable, and we’ll do our best to create the best Fire Alarm Cable for your business!
Adding extra value to your Fire Alarm Cable by choosing a suitable Fire Alarm Cable design is also a key element to boost your brand in promoting Fire Alarm Cable. Fashionable, technical, and practical shapes for Fire Alarm Cable or packages for Fire Alarm Cable could increase customers’ desire to try your Fire Alarm Cable. By creating a specialized label for Fire Alarm Cable or a design of Fire Alarm Cable, it is easier to create a better and more lasting impression on your target market for selling Fire Alarm Cable.
After completing the production of your Fire Alarm Cable, our selection of labels as well as packages for Fire Alarm Cable is designed to cater to your special wants if your need to add your trademarks on the surface of Fire Alarm Cable. We offer different designs for Fire Alarm Cable and types of packages for Fire Alarm Cable that can drastically enhance the way your Fire Alarm Cable is consumed. Custom labeling services can also be requested to complement your unique needs for Fire Alarm Cable. Contact us now!
Sunshine Electronics targets at supplying the best customer experience in the whole cooperation process of Fire Alarm Cable. We also offer free samples for Fire Alarm Cable to all clients who are willing to have a try on our high-quality Fire Alarm Cable. After getting your free samples of Fire Alarm Cable, you can check and examine our Fire Alarm Cable if our Fire Alarm Cable meets your requirements. We undoubtedly possess the confidence that our Fire Alarm Cable is of premium quality and you will not regret.
Fire Alarm Cable meets the following industry standards:
Fire Alarm cable is composed of solid bare conductors. Our Fire Alarm cable is also twisted for maximum flexibility. A fire Alarm cable is also available in Riser or Plenum. The fire Alarm can also be shielded with aluminum foil and a stranded tinned copper drain wire.
In fire alarm systems, the real difference between Class B and Class A is that if the pathway is interrupted, Class B only sends a "Failure Signal" to the panel, and Class A provides an extra path to get around the interruption.
According to NEC Articles 760 and 725, there are two types of fire alarm system circuits: power restricted and non-power-limited. Power Limited Fire Alarm Wires typically work at 24 volts DC, whereas non-power-limited cables run at 120 volts AC.
Type 1 - Cable with a resistance of fewer than 100 Ohms/km and low smoke zero halogen insulating and sheathing. Type 2 - Cable with a resistance of fewer than 100 Ohms/km and PVC insulation and sheathing.
Conduit or not to Conduit? NFPA and NEC 90 articles state that when installing a fire alarm system, any fire alarm wiring below 7 feet or in non-accessible areas must be installed in a metallic raceway, including behind drywall walls or hard ceiling surfaces.
If fire alarm cabling does not have other wires or cabling nearby or other sources of electrical interference, you may not need shielding. But in facilities near heavy electrical or mechanical equipment, the interference from these devices might mean you should use shielding to protect the fire alarm cable.
Power-limited fire alarm circuit cables and conductors shall not be placed in any cable, cable tray, compartment, enclosure, manhole, outlet box, device box, raceway, or similar fitting with conductors of electric light, power, Class 1, non—power-limited fire alarm circuits, and medium-power network-powered broadband ...
